Lefisc
New member
- Thread Author
- #1
Big Update on Verizon Quantum
I had a huge problem with the new system, now resolved. Of course, people on out site may seem fussy to Verizon, but we do know what we are talking about. Let me give you the short version and then, if you have the patience a bit more detail.
I wrote, “The unit gives better contrast and color than the previous units, but with a slight loss of detail... The sound seems a bit thinner…” I was damn right. But the controls went from being sluggish to totally none responsive and I lost the picture and sound TOTALLY on my “slave” units! Verizon came today, Sunday, and after nearly 3 hours fixed it.
Now, the picture and sound are better than when first installed and better than the old system, going from 720P to 1080P
The cause: An incompetent first installer and deliberately inept service at Verizon.
The details:
After watching the picture weaken and losing into totally on Friday, after 2 hours on the phone, I asked for the old service to be returned. They came today, Sunday, at 9 AM.
The GOOD installer wanted the check out the new system before replacing it. He pulled up on the screen a NEW guide that measured the signal and “computer switching” strength of the system.
This is something the FIRST installer should have done. He told me that the three “slaves” should all have signals near 650. They had signals barely past 500.
The FIRST installer was supposed to replace the obsolete and old relays and switchers, he didn’t even check them. So the new guy did and the signal strength jumped to where it should be. The picture got better and the sound fuller and louder. (This took time because everything needed to be rebooted). Let me stress checking this is mandatory for a new install, especially when there was old, old wiring but the first guy didn’t do his job.
MORE: The first installer set my TVs to 1080i, but the new units do 1080p. There were a few other setting too that we adjusted.
We had to “turn on” the DVR service again (or refresh it from Verizon). Here is the deliberate ineptness. This too nearly an hour. Verizon WILL NOT give the installers access to this. They have to call in, wait for a service operator and they have to do it. Then they call back the servicemen, wasting his time and mine. The serviceman suspects that Verizon doesn’t want too much control with one person, but this added a huge amount of time to the service.
In addition, the people who teach the installers NEVER have installed anything, they have no field experience whatsoever. So they don’t know how to handle real work situations.
While I would not say this is a Quantum leap from the last system, it’s a nice jump. I can record 6 programs at once and the picture and sound seem better. They need a menu (software) update and I am sure that will come this millennium. Again it only cost me $1 a month.
I had a huge problem with the new system, now resolved. Of course, people on out site may seem fussy to Verizon, but we do know what we are talking about. Let me give you the short version and then, if you have the patience a bit more detail.
I wrote, “The unit gives better contrast and color than the previous units, but with a slight loss of detail... The sound seems a bit thinner…” I was damn right. But the controls went from being sluggish to totally none responsive and I lost the picture and sound TOTALLY on my “slave” units! Verizon came today, Sunday, and after nearly 3 hours fixed it.
Now, the picture and sound are better than when first installed and better than the old system, going from 720P to 1080P
The cause: An incompetent first installer and deliberately inept service at Verizon.
The details:
After watching the picture weaken and losing into totally on Friday, after 2 hours on the phone, I asked for the old service to be returned. They came today, Sunday, at 9 AM.
The GOOD installer wanted the check out the new system before replacing it. He pulled up on the screen a NEW guide that measured the signal and “computer switching” strength of the system.
This is something the FIRST installer should have done. He told me that the three “slaves” should all have signals near 650. They had signals barely past 500.
The FIRST installer was supposed to replace the obsolete and old relays and switchers, he didn’t even check them. So the new guy did and the signal strength jumped to where it should be. The picture got better and the sound fuller and louder. (This took time because everything needed to be rebooted). Let me stress checking this is mandatory for a new install, especially when there was old, old wiring but the first guy didn’t do his job.
MORE: The first installer set my TVs to 1080i, but the new units do 1080p. There were a few other setting too that we adjusted.
We had to “turn on” the DVR service again (or refresh it from Verizon). Here is the deliberate ineptness. This too nearly an hour. Verizon WILL NOT give the installers access to this. They have to call in, wait for a service operator and they have to do it. Then they call back the servicemen, wasting his time and mine. The serviceman suspects that Verizon doesn’t want too much control with one person, but this added a huge amount of time to the service.
In addition, the people who teach the installers NEVER have installed anything, they have no field experience whatsoever. So they don’t know how to handle real work situations.
While I would not say this is a Quantum leap from the last system, it’s a nice jump. I can record 6 programs at once and the picture and sound seem better. They need a menu (software) update and I am sure that will come this millennium. Again it only cost me $1 a month.