A Leap of Faith, sort of, thanks to Paul Yoo - The MISHO MYRONOV TUBE WOODENAMP and PREAMP!
- Thread starter joeinid
- Start date
Paul
Senior Member
In terms of pre , Signal come in, goes through a single pair of very high quality Siemens C3M tubes (not the normal 12ax7, 12at7, etc.), directly connected to some amazing output transformers, then to the volume attenuator, then RCA out. That's it, a single gain stage with some of the best valves ever made. If you can find a more transparent and dynamic pre I'd love to hear it
For the EL12 Amps. I find it very hard to go back to other amps. They don't have the dynamics, life and low level resolution of Mishos Wooden amps
For the EL12 Amps. I find it very hard to go back to other amps. They don't have the dynamics, life and low level resolution of Mishos Wooden amps
Rob181
Member
How does one contact Misho...
- Thread Author
- #24
His email is as follows:
[email protected]
Michael is his first name. I think he might be on vacation as Paul mentioned.
- Thread Author
- #30
That is a great question. I am not sure but I think he either winds it himself or has it done specifically for him.
I've tried and MC275VI, MC303, MC452, Job INTegrated, Valvet E2, Dennis Had 45 monos, Cary 300B-SE, ASL Wave monos, Job 250 monos, Jolida 3502, Luxman MQ-300B, SIT3 and Naim Supernait2 and probably a few more than I remember.
Last edited:
- Thread Author
- #31
Hi Parker,
Import was a breeze. My normal mailman delivered them. Not sure if it's called EMS post or similar. The only thing was that the preamp was held up in customs for almost a week. The amp sailed right through and both packages were is awesome shape, better than I expected. No additional duty or anything to my home in NY.
Paul
Senior Member
Jack
Active member
And XA-25
- Thread Author
- #34
- Thread Author
- #35
Jack
Active member
Sounds like you have the perfect setup now with the Wooden's.
Paul
Senior Member
Add to your lists I can go on few myself as well.
Accuphase E650
Kondo Overture
Finale Audio 6V6 ( these 3 currently I have with Wooden set up )
Thöress F2A11
AirTight ATM3 monos
Audio Aero 211 monos
Avantgarde Int amp
McIntosh 2301’s
I may forget few as well.
Sent from my iPhone using Tapatalk
Accuphase E650
Kondo Overture
Finale Audio 6V6 ( these 3 currently I have with Wooden set up )
Thöress F2A11
AirTight ATM3 monos
Audio Aero 211 monos
Avantgarde Int amp
McIntosh 2301’s
I may forget few as well.
Sent from my iPhone using Tapatalk
- Thread Author
- #38
I absolutely do and I'm extremely lucky.
Between the Misho and GAT2 preamps, the Misho amp, Valvet E2, and SIT3, I have it all covered. The Luxman MQ300 is a wonderful 300B amp but doesn't get as much playtime these days. I'll have to think about what gets listed for sale next.
Sent from my SM-N910P using Tapatalk
- Thread Author
- #39
I'll have to try an E650 but I'm not sure it'll best what I have now. Having an integrated could be a wonderful thing, though. The Luxman class A integrated could be just as good
Sent from my SM-N910P using Tapatalk
Audio-Antiquary
New member
- Joined
- Apr 5, 2019
- Messages
- 34
Thank you Joe and Paul for a great words about my amps!
To answer some questions - each audio transformer used in my amps is designed and made by me. Each designed specifically for the task, and has been heavily prototyped, tested, auditioned and redesigned and again and again untill I was happy not with the sound OR measurements only, but both.
All my amps completely designed by me, the basic principles - simplicity, transformer coupled stages and transformer outputs.
The wooden chassis has a complex structure, each layer designed to accommodate corresponding parts, and after glueing together it become a "solid plywood" 3D unit
Warranty and service - I'm sure provide full service support for my amps, life long. But it will not be needed most likely - if amps used in a correct way and not abused - it will serve troubleless for decades. It was designed this way
Do not hesitate to ask questions, I will be happy to answer (if not going too deep where proprietary things are starting
And very important note - each amp is made by my own two hands, so production capability is very limited.
I'm trying to carefully plan my working schedule so there will be no dead ends in production.
I have no amps on a shelves (I wish but everything is gone immediately), so no sales as such but only making on orders.
Best regards,
Misho
To answer some questions - each audio transformer used in my amps is designed and made by me. Each designed specifically for the task, and has been heavily prototyped, tested, auditioned and redesigned and again and again untill I was happy not with the sound OR measurements only, but both.
All my amps completely designed by me, the basic principles - simplicity, transformer coupled stages and transformer outputs.
The wooden chassis has a complex structure, each layer designed to accommodate corresponding parts, and after glueing together it become a "solid plywood" 3D unit
Warranty and service - I'm sure provide full service support for my amps, life long. But it will not be needed most likely - if amps used in a correct way and not abused - it will serve troubleless for decades. It was designed this way
Do not hesitate to ask questions, I will be happy to answer (if not going too deep where proprietary things are starting
And very important note - each amp is made by my own two hands, so production capability is very limited.
I'm trying to carefully plan my working schedule so there will be no dead ends in production.
I have no amps on a shelves (I wish but everything is gone immediately), so no sales as such but only making on orders.
Best regards,
Misho