Turntable , location?

jay.goodman1

New member
Joined
May 19, 2020
Messages
11
Location
US
Revamped my av config..mid-fi stuff

Have any of you set up a home theater system and then wondered where to put your turntable?

I'm thinking about a slide-out shelf but it's still right next to us center speaker..and obvious isolation issues..

It used to sit on top of this tall rack in the picture but I can't figure out how to make it fit in this configuration....

Thoughts?

hsu 5.1pkg w/ vtf-15 sub
Denon x3600 avr
be7e9dc3b3bd5ba024ee1fe1442b80f6.jpg
8ff09c2b3df5625761618e3fbaa30dfd.jpg


Sent from my SM-G960U using Tapatalk
 
May be a little off balance but slide the cabinet far left or right to edge of TV and may give you room for the TT, see if moving speakers towards you and slightly out? It may balance things out?


Sent from my iPhone using Tapatalk Pro
 
You could...
1. Move existing rack (the one that TV sits on) to the side wall. Then set turntable on top of that rack.
2. Get different base for TV or hang TV from ceiling.
3. Buy longer speaker cables.
 
Other thoughts....

IF i wanted to place dedicated TT shelf to right wall, 15' away from main system, is than issue?

Rca cables would need to be 20' long....

----------------------------------------------
TV/avr
Lspkr. Cntr. Rspkr.



--- Seating ----. --->> TT


Sent from my SM-G960U using Tapatalk
 
Jay - In general the signal level from a turntable is relatively low and as such is more susceptible to degradation from long cable runs. It is therefore preferred if you could keep the cable from the tonearm to your phono input as short as possible. One way to achieve this is if you have a stand alone phono stage which can be positioned closer to the turntable, connect it directly and you can then run longer interconnects from the phono stage outputs to your line stage preamplifier. The phono signal after going through the phono stage is at line level which is much less affected by going through a longer length of cable. That's really the most effective way of avoiding long runs of cable carrying the low level phono signal. If it can't be avoided you can try running 20' cables from your turntable into your preamp and it may work but it's not optimal and can definitely compromise performance. Hope that helps.
 
Jay - In general the signal level from a turntable is relatively low and as such is more susceptible to degradation from long cable runs. It is therefore preferred if you could keep the cable from the tonearm to your phono input as short as possible. One way to achieve this is if you have a stand alone phono stage which can be positioned closer to the turntable, connect it directly and you can then run longer interconnects from the phono stage outputs to your line stage preamplifier. The phono signal after going through the phono stage is at line level which is much less affected by going through a longer length of cable. That's really the most effective way of avoiding long runs of cable carrying the low level phono signal. If it can't be avoided you can try running 20' cables from your turntable into your preamp and it may work but it's not optimal and can definitely compromise performance. Hope that helps.
I actually have 20' interconnects from my previous home...
So i would need a phone preamp , sit next to TT, and run interconnects...

I play vinyl infrequently...
Any recommendation on Preamp?

Thank you

Sent from my SM-G960U using Tapatalk
 
I'd recommend placing the phono stage next to the turntable, and running XLR cables from the phono stage to the rest of your gear if that would be a 20' long run.
 
I'd recommend placing the phono stage next to the turntable, and running XLR cables from the phono stage to the rest of your gear if that would be a 20' long run.

Totally agree. And the cables can be Blue Jeans Cable (well-built and inexpensive).
 
I’m satisfied with bluejeans (Belden) speakers cable.

Highly recommended


Sent from my iPhone using Tapatalk
 
Back
Top