Lumin d2 display issues

MRJAZZ

MRJAZZ

Member
Joined
Nov 19, 2013
Messages
206
My D2 is having issues with the display. It doesn't always turn on once powered up. It takes turning on and off the power numerous times before it ( the display) finally comes on. There is nothing wrong with the power cord as the Ethernet port shows it is receiving a signal (blinking green light shows that the Ethernet port is working) but yet the display isn't on. In settings I have the display set to never turn off. Any thoughts as to whats wrong?
 
That is strange..!!!

First time I read something about display problem or problems with D2.

Hope you can solve it soon.
 
Have you tried a reset by taking a pin and putting it in the hole labeled reset on the back panel? I’m not sure it’ll fix your problem but that’s what I would do if it were mine.
 
Even if the display is not showing anything, can Lumin app see the D2 on network and play normally 30 seconds after it boots up?

Are you using a third party LPS?
 
wklie said:
Even if the display is not showing anything, can Lumin app see the D2 on network and play normally 30 seconds after it boots up?

Are you using a third party LPS?
Click to expand...

The LUMIN app doesn’t see the D2 when this happens. I am not using a third party LPS.
 
Hi Peter,

I have the same identical problem.

At the beginning, after some on/off the Lumin D2 started .

Now the lan's led are on but the Lumin D2 won't boot. Reset doesn't work.
 
Having the Lumin D2 for over a year I noticed same issue with display.
(I had connected th D2 to an Sbooster wich gave to my ears better performance)
' Playin' with the on and off switch from the Sbooster solved the display problem now and then.
Recently I ordered the remote control (not so cheap) and switched the Lumin on and off by the remote.That worked fine for 1 to 2 months but then the same display issue came back.
My simple guess is that there maybe some hardware weakness in the product.
Fortunately I also own an Auralic so I can
still stream music. (but I liked the sound signature of the D2 a bit more)
 
Well my D1 in the other room had a similar problem and after getting with Peter it turned out it was the power supply that was going bad. Ordered a similar spec'd supply, problem resolved. It was intermittent flaky until the Lumin would not turn on at all.
 
Hi Peter,

I have the similar problem on my Lumin D2 after using 3 years

Now the lan's led are on but the Lumin D2 won't boot. Reset doesn't work. I am not using a third party LPS. I checked it Fuse, looks clean

Any thoughts as to whats wrong?
 
I have a Lumin D1 .. same issue. I did swap to a Sbooster Power supply. It didn’t resolve the issue. I looked at the specs on the original power brick and it’s a 4 Amp power supply.. I don’t know if the Sbooster has enough current output
 
For troubleshooting D1, please try another SMPS like the factory 12V 4A power supply, but not an LPS. An alternative compatible brand is Meanwell 12V 5.5mm x 2.1mm.
 
jpeg said:
Hi Peter,

I have the similar problem on my Lumin D2 after using 3 years

Now the lan's led are on but the Lumin D2 won't boot. Reset doesn't work. I am not using a third party LPS. I checked it Fuse, looks clean

Any thoughts as to whats wrong?
Click to expand...

Hi folks,
I am having a similar problem. The app on my iPhone or iPad won’t recognize the Lumin D2 and the display won’t come on. The Ethernet lights blink, the fuse is good, the power cord is good but the Lumin display is not working. I haven’t had any problems prior to today and all of a sudden I get nothing.
In the app I cannot access my Qobuz account either if that might be a clue? I tried to contact wklie for some assistance but I’m a new member and don’t have permission yet to do pm’s yet.
If you folks came up with a solution I would love to know how you fixed it. Thanks for any advice!
Erik
 
ErikL said:
Hi folks,
I am having a similar problem. The app on my iPhone or iPad won’t recognize the Lumin D2 and the display won’t come on. The Ethernet lights blink, the fuse is good, the power cord is good but the Lumin display is not working. I haven’t had any problems prior to today and all of a sudden I get nothing.
In the app I cannot access my Qobuz account either if that might be a clue? I tried to contact wklie for some assistance but I’m a new member and don’t have permission yet to do pm’s yet.
If you folks came up with a solution I would love to know how you fixed it. Thanks for any advice!
Erik
Click to expand...
Mine was eventually repaired by the US IMPORTER. I don’t recall what specifically was replaced/repaired, but they had to put in a new board. I suggest you contact them directly. I don’t have their number, but I am sure someone here has it.
 
Thanks MRJAZZ!
I was hoping it was something simple I could fix. I’ve got my fingers crossed! Kind of a bummer if it requires outside service as I’m out of warranty.
Regards
Erik
 
You must log in or register to reply here.
Back
Top