JOB 225 2-channel Power Amplifier ... update ...

[XV-1]

Has Job closed its doors?

[joeinid]

Yes.

There maybe something in the future, but I believe all operations except repair are over.

Has Job closed its doors?

[lesc]

Hello,

I've owned a JOB 225 since 2013 but for the past 3+ years I've been having some serious technical issues. Initially it started with just slight noises from the right channel, which ultimately worsened into really LOUD "pops." Now the amp won't even turn on. Interestingly, when it was operational the popping sounds stopped after 20 minutes or so.

Does anyone know any reputable repair options in the NYC area? I'm even considering sending the amp board to Switzerland... It will be expensive but considering the cost of something equivalent, I think it might be worthwhile still.

Thank you in advance.

Les

[joeinid]

Welcome to the forum Les, thank you for joining.

Send an email to service@jobsys.com

They should be able to help.

[applecross]

Hi all,

I have Job 225 coming next week. I am very late to the party I know.
With Job Systems being shut it's a bit of a gamble but having read about this amp, when I saw a classified for £700 I just pulled the trigger.

I am actually putting together a system for the first time and I have a few questions.

Attenuation and preamp matching
I will be driving the Job 225 from the RCA pre out of an RME ADI2 DAC. To deal with the high gain I am able to set the reference level output to -5dBu (the default is +7dBu or 1.73 VRMS). Do I still need attenuators from Rothwell audio? If yes, is 10db enough or will I need more? I plan to order the Rothwell River interconnects with Switchcraft plugs.

RME specs:
Analog Outputs
XLR

• Output level switchable +19 dBu, +13 dBu, +7 dBu, +1 dBu @ 0 dBFS
• Signal to Noise ratio (SNR) @ +7/+13/+19 dBu: 117 dB RMS unweighted, 120 dBA
• Signal to Noise ratio (SNR) @ +1 dBu: 115,4 dB RMS unweighted, 118,9 dBA
• Frequency response @ 44.1 kHz, -0.1 dB: 0 Hz – 20.2 kHz
• Frequency response @ 96 kHz, -0.5 dB: 0 Hz – 44.9 kHz
• Frequency response @ 192 kHz, -1 dB: 0 Hz – 88 kHz
• Frequency response @ 384 kHz, -1 dB: 0 Hz – 115 kHz
• Frequency response @ 768 kHz, -3 dB: 0 Hz – 109 kHz
• THD @ -1 dBFS: -112 dB, 0.00025 %
• THD+N @ -1 dBFS: -110 dB, 0.00032 %
• THD @ -3 dBFS: -116 dB, 0.00016 %
• Channel separation: > 120 dB
• Output impedance: 200 Ohm balanced, 100 Ohm unbalanced

Chinch
As output XLR, but:

• Output: 6.3 mm TS jack, unbalanced
• Output level 6 dB lower than XLR (-5 dBu to +13 dBu @ 0 dBFS)
• Signal to Noise ratio (SNR) @ +13 dBu: 117 dB RMS unweighted, 120 dBA
• Signal to Noise ratio (SNR) @ +1/+7 dBu: 114/116 dB RMS unweighted, 117/119 dBA
• Signal to Noise ratio (SNR) @ -5 dBu: 109 dB RMS unweighted, 113 dBA

Power cord matching
The general consensus among reviewers seems to be that an aftermarket power cord makes a substantial difference. Can anyone confirm this is the case? If so, what cords are a good match?
I am keen on a Oyaide GPXe v2, but given the price I want to be sure of the benefits.

Fuse swap
I came across a review which suggests to swap the stock fuse with a Telos QBT-18.Has anyone tried this? What is the stock fuse and which specifications should I order if I want to replace it?

Manual
I do not have a copy of the manual. Does anyone have one in PDF and can PM it to me?

Thanks in advance!

[joeinid]

Welcome to the forum. Thank you for joining.

Hi all,

I have Job 225 coming next week. I am very late to the party I know.
With Job Systems being shut it's a bit of a gamble but having read about this amp, when I saw a classified for £700 I just pulled the trigger.

I am actually putting together a system for the first time and I have a few questions.

Attenuation and preamp matching
I will be driving the Job 225 from the RCA pre out of an RME ADI2 DAC. To deal with the high gain I am able to set the reference level output to -5dBu (the default is +7dBu or 1.73 VRMS). Do I still need attenuators from Rothwell audio? If yes, is 10db enough or will I need more? I plan to order the Rothwell River interconnects with Switchcraft plugs.

RME specs:
Analog Outputs
XLR

• Output level switchable +19 dBu, +13 dBu, +7 dBu, +1 dBu @ 0 dBFS
• Signal to Noise ratio (SNR) @ +7/+13/+19 dBu: 117 dB RMS unweighted, 120 dBA
• Signal to Noise ratio (SNR) @ +1 dBu: 115,4 dB RMS unweighted, 118,9 dBA
• Frequency response @ 44.1 kHz, -0.1 dB: 0 Hz – 20.2 kHz
• Frequency response @ 96 kHz, -0.5 dB: 0 Hz – 44.9 kHz
• Frequency response @ 192 kHz, -1 dB: 0 Hz – 88 kHz
• Frequency response @ 384 kHz, -1 dB: 0 Hz – 115 kHz
• Frequency response @ 768 kHz, -3 dB: 0 Hz – 109 kHz
• THD @ -1 dBFS: -112 dB, 0.00025 %
• THD+N @ -1 dBFS: -110 dB, 0.00032 %
• THD @ -3 dBFS: -116 dB, 0.00016 %
• Channel separation: > 120 dB
• Output impedance: 200 Ohm balanced, 100 Ohm unbalanced

Chinch
As output XLR, but:

• Output: 6.3 mm TS jack, unbalanced
• Output level 6 dB lower than XLR (-5 dBu to +13 dBu @ 0 dBFS)
• Signal to Noise ratio (SNR) @ +13 dBu: 117 dB RMS unweighted, 120 dBA
• Signal to Noise ratio (SNR) @ +1/+7 dBu: 114/116 dB RMS unweighted, 117/119 dBA
• Signal to Noise ratio (SNR) @ -5 dBu: 109 dB RMS unweighted, 113 dBA

Power cord matching
The general consensus among reviewers seems to be that an aftermarket power cord makes a substantial difference. Can anyone confirm this is the case? If so, what cords are a good match?
I am keen on a Oyaide GPXe v2, but given the price I want to be sure of the benefits.

Fuse swap
I came across a review which suggests to swap the stock fuse with a Telos QBT-18.Has anyone tried this? What is the stock fuse and which specifications should I order if I want to replace it?

Manual
I do not have a copy of the manual. Does anyone have one in PDF and can PM it to me?

Thanks in advance!

[applecross]

Thank you!

Bumping thread again if anyone can answer my questions.

I also have an additional one: I have my eyes on a SL Audio e112 sub-woofer that has line in and line out, via an internal Linkwitz–Riley cross over.
Given the Job's sensitivity would it be possible to have the set up as PREAMP > SUB CROSSOVER > JOB 225?

[Randy Myers]

I have had the Job 225 amplifier a couple times. I always felt it was a great little amp, a real bargain. When I have had it I used Rothwell's with it which seemed to help.

[applecross]

I have had the Job 225 amplifier a couple times. I always felt it was a great little amp, a real bargain. When I have had it I used Rothwell's with it which seemed to help.

Hello Randy,

I think I will order the River interconnects and the attenuators. Just to be sure!

[Jack]

I've owned both the Job 225 and it's sibling the Nuforce STA-200 which is even more sensitive. Looking at the options available for gain using the RCA (Cinch) connections you should have no problem finding one of the available settings that will work without the Rothwells. In fact all of them should work except the highest one.