Welcome to the AudioShark Forums.
Results 1 to 38 of 38
  1. #1
    Senior Member
    Join Date
    Dec 2018
    Location
    Salem VA
    Posts
    174

    New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Hey all,

    Well, my new MQ88-uSE shipped directly from Luxman 2 weeks ago suddenly started making horrendous cracking and popping noises in the left channel last night.

    I swapped sides with all the power tubes and it went away, so I figured maybe one of the left channel tubes wasn't seated properly.

    Tonight after listening for about 2 hours, suddenly the same tube (I assume, now in the right channel) started arcing and sparking inside the tube with the same loud crackling coming now from my right speaker.

    I have no idea what is happening - being a brand new amp, and moreso being a "SE" with premium matched KT88s, this is extremely frustrating. I've had to shut down my entire system until I can get it sussed out, which I assume at the minimum will be getting new tubes from Luxman, and possibly having to ship it back for repair, after only owning for 2 weeks.

    Anyone have any ideas what may be happening here? Could a connection be causing a short? I'm running the output from the Backert Labs Rhumba Extreme directly into the inputs on the Luxman.

    Thanks in advance
    PRIMARY 2 CH SYSTEM: Backert Labs Rhythm 1.3; Parasound JC3+ Phono pre; Luxman M900u; Pure Fidelity Harmony with Origin Live Illustrious tonearm and PF Stratos cart; Naim NDX 2; Naim 555PS; Innuos Zen MK III (Roon Core); EtherRegen; Volti Audio Rivals; JL Audio e112 (2); Transparent Super Speaker Cables; Transparent Super interconnects; Transparent Premium & High Performance power cables; Naim Fraim; Stillpoints Ultra SS; Symposium Ultra platforms; IsoTek EVO3 Sigmas conditioner; GIK Acoustics absorption and diffusion panels

  2. #2
    Senior Member
    Join Date
    May 2013
    Location
    Tallahassee, Florida/Greenville, SC
    Posts
    3,242

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Sometimes even new tubes go bad. If you are going to run the amp on a regular basis then you need to have a spare quad of KT-88's anyway and you don't want to wait on a tube to be shipped from Japan anyway. Go to Tube Depot, The Tube Store or even Viva Tubes in Easthampton, Ma. and order a matched quad of Genalex Gold Lion KT-88's. The tubes that come with the amp are just rebranded JJ's. Viva has a matched quad for $175 for the Genalex and $163 for the JJ's. Has nothing to do with the preamp.
    Main - JVC QL-Y7/Denon DL-301 Mk II, Gold Note PH-10, Jays CDT3 Mk3 , Auralic Aries G2.2, Holo May KTE, Supratek Cabernet, Kinki Studio EX-B7 monoblocks, Verity Audio Otello, (2) Rythmik F12SE, Audio Envy IC, SC & PC's, Triode Wire Lab PC's, Inakustik USB and I2S, (2) Puritan Audio Labs PSM-156 with Groundmaster City, Timbernation rack

    Family Room - Oppo UDP-203, Auralic Aries, Aqua La Voce S3, Kinki Studio EX-M1+, Nola KO, (2) Rythmik F-12G, Wireworld SC & IC's, Neotech PC's, SurgeX SA-1810

    Greenville, SC- Jays CDT2 Mk 3, Auralic Aries G1, Holo Spring 3 KTE, Supratek Chardonnay, Odyssey Audio Kismet Reference, Rosso Fiorentino Volterra 2, (2) RSL Speedwoofers, iFi Audio Power Station, Wireworld IC's, Inakustik USB and I2s, Triode Wire Lab SC, Triode Wire Lab PC's, Furutech NCF Clear Line, Timbernation rack.

  3. #3
    Senior Member
    Join Date
    Dec 2018
    Location
    Salem VA
    Posts
    174

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Thanks, I can grab a quad of KT-88s somewhere and I assume Luxman has some kind of warranty for their "hand matched" special edition tubes that are less than 2 weeks old. Resale would take quite a hit without original Luxman tubes I imagine?

    Anyway - a concern is what could be causing it... is it 99% likely it's just a bad tube from Luxman, or could there be a power issue elsewhere in the amp that cause the tube to fail?

    Thanks!
    PRIMARY 2 CH SYSTEM: Backert Labs Rhythm 1.3; Parasound JC3+ Phono pre; Luxman M900u; Pure Fidelity Harmony with Origin Live Illustrious tonearm and PF Stratos cart; Naim NDX 2; Naim 555PS; Innuos Zen MK III (Roon Core); EtherRegen; Volti Audio Rivals; JL Audio e112 (2); Transparent Super Speaker Cables; Transparent Super interconnects; Transparent Premium & High Performance power cables; Naim Fraim; Stillpoints Ultra SS; Symposium Ultra platforms; IsoTek EVO3 Sigmas conditioner; GIK Acoustics absorption and diffusion panels

  4. #4
    Senior Member
    Join Date
    May 2013
    Location
    Tallahassee, Florida/Greenville, SC
    Posts
    3,242

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    There is really nothing that can be "special" about the JJ tubes other than how closely they may have matched them. They just buy enough to have their label silk screened on just like Primaluna does with Shuguang. They say right on their website that they are just JJ tubes and after a year having new tubes in place will increase the value. When you get the replacement from Luxman just set them aside and use the Gl's which are a better tube anyway. Yes that is the most likely cause with a new power tube especially from certain brands. If a second one blows out in the same position then you may have a problem but since the problem followed the tube only then it is the tube.
    Main - JVC QL-Y7/Denon DL-301 Mk II, Gold Note PH-10, Jays CDT3 Mk3 , Auralic Aries G2.2, Holo May KTE, Supratek Cabernet, Kinki Studio EX-B7 monoblocks, Verity Audio Otello, (2) Rythmik F12SE, Audio Envy IC, SC & PC's, Triode Wire Lab PC's, Inakustik USB and I2S, (2) Puritan Audio Labs PSM-156 with Groundmaster City, Timbernation rack

    Family Room - Oppo UDP-203, Auralic Aries, Aqua La Voce S3, Kinki Studio EX-M1+, Nola KO, (2) Rythmik F-12G, Wireworld SC & IC's, Neotech PC's, SurgeX SA-1810

    Greenville, SC- Jays CDT2 Mk 3, Auralic Aries G1, Holo Spring 3 KTE, Supratek Chardonnay, Odyssey Audio Kismet Reference, Rosso Fiorentino Volterra 2, (2) RSL Speedwoofers, iFi Audio Power Station, Wireworld IC's, Inakustik USB and I2s, Triode Wire Lab SC, Triode Wire Lab PC's, Furutech NCF Clear Line, Timbernation rack.

  5. #5
    Senior Member
    Join Date
    Dec 2018
    Location
    Salem VA
    Posts
    174

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Quote Originally Posted by Jack View Post
    There is really nothing that can be "special" about the JJ tubes other than how closely they may have matched them. They just buy enough to have their label silk screened on just like Primaluna does with Shuguang. They say right on their website that they are just JJ tubes and after a year having new tubes in place will increase the value. When you get the replacement from Luxman just set them aside and use the Gl's which are a better tube anyway. Yes that is the most likely cause with a new power tube especially from certain brands. If a second one blows out in the same position then you may have a problem but since the problem followed the tube only then it is the tube.
    Thanks - I wonder if it’s possible to run 120s in place of the 88s. I could pull the Tung Sols from my Rogue while I wait on new JJs from Luxman.

  6. #6
    Senior Member
    Join Date
    May 2013
    Location
    Tallahassee, Florida/Greenville, SC
    Posts
    3,242

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Not likely as not shown on the spec sheet or mentioned in description. You are just going to have to break down and buy a set while you wait on Luxman to do anything or you may be down a while. Always have spare power tubes. If that amp has manual biasing you could get away with just buying a pair while you wait to see if they are going to send you a new quad or just one. Actual info on the website is sparse at best.
    Main - JVC QL-Y7/Denon DL-301 Mk II, Gold Note PH-10, Jays CDT3 Mk3 , Auralic Aries G2.2, Holo May KTE, Supratek Cabernet, Kinki Studio EX-B7 monoblocks, Verity Audio Otello, (2) Rythmik F12SE, Audio Envy IC, SC & PC's, Triode Wire Lab PC's, Inakustik USB and I2S, (2) Puritan Audio Labs PSM-156 with Groundmaster City, Timbernation rack

    Family Room - Oppo UDP-203, Auralic Aries, Aqua La Voce S3, Kinki Studio EX-M1+, Nola KO, (2) Rythmik F-12G, Wireworld SC & IC's, Neotech PC's, SurgeX SA-1810

    Greenville, SC- Jays CDT2 Mk 3, Auralic Aries G1, Holo Spring 3 KTE, Supratek Chardonnay, Odyssey Audio Kismet Reference, Rosso Fiorentino Volterra 2, (2) RSL Speedwoofers, iFi Audio Power Station, Wireworld IC's, Inakustik USB and I2s, Triode Wire Lab SC, Triode Wire Lab PC's, Furutech NCF Clear Line, Timbernation rack.

  7. #7
    Senior Member
    Join Date
    Dec 2018
    Location
    Salem VA
    Posts
    174

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Thanks, just placed an order for the matched quad set of GLs on Viva Tube. In the meantime, I guess it's back to listening to the office system until I get this sorted out.
    PRIMARY 2 CH SYSTEM: Backert Labs Rhythm 1.3; Parasound JC3+ Phono pre; Luxman M900u; Pure Fidelity Harmony with Origin Live Illustrious tonearm and PF Stratos cart; Naim NDX 2; Naim 555PS; Innuos Zen MK III (Roon Core); EtherRegen; Volti Audio Rivals; JL Audio e112 (2); Transparent Super Speaker Cables; Transparent Super interconnects; Transparent Premium & High Performance power cables; Naim Fraim; Stillpoints Ultra SS; Symposium Ultra platforms; IsoTek EVO3 Sigmas conditioner; GIK Acoustics absorption and diffusion panels

  8. #8
    Senior Member
    Join Date
    Nov 2015
    Location
    Kansas
    Posts
    5,948

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    I had a set of the Golden Lion with an ARC a while back. They were nice tubes.

    Anything can have a bad one. I had a brand new set of Black Treasures; they were pretty darn expensive. One was arcing right out of the box. It was replaced and the replacement worked just fine afterwards!
    McIntosh C49, MC152, MR85, R778 | T+A DAC 8 DSD | KEF LS50 Meta w/S2, KC62 (x2) | Rega RP8, Ania Pro, NEO PSU | Technics SL-1500C | Audio Technica VM750ML | Hexmat Eclipse, Yellow Bird, Molekula, Molekula Mini | Pro-Ject VC-E | Falcon NW PC Server (Roon Core & HQPlayer) | Microsoft Surface Pro 6 (Roon Controller) | Abyss Diana Phi | Schiit Jotunheim 2 | Astell&Kern SE200 | Oppo BDP105

    “One of the great challenges in life is knowing enough to think you're right but not enough to know you're wrong”
    "You can't use reason to convince anyone out of an argument that they didn't use reason to get into"
    ― Neil deGrasse Tyson

  9. #9
    Senior Member
    Join Date
    Dec 2018
    Location
    Salem VA
    Posts
    174

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Thanks guys... my biggest worry was that something may have happened to the amp itself but it sounds like we're all right.

    From a tube standpoint, the Gold Lions are delivering next Tuesday and Luxman has ordered another matched pair of 88s from Japan (covered under warranty), which will likely arrive late next week. So I will have the new GLs to demo and a clean set of JJs from Luxman.

    Best of all outcomes!
    PRIMARY 2 CH SYSTEM: Backert Labs Rhythm 1.3; Parasound JC3+ Phono pre; Luxman M900u; Pure Fidelity Harmony with Origin Live Illustrious tonearm and PF Stratos cart; Naim NDX 2; Naim 555PS; Innuos Zen MK III (Roon Core); EtherRegen; Volti Audio Rivals; JL Audio e112 (2); Transparent Super Speaker Cables; Transparent Super interconnects; Transparent Premium & High Performance power cables; Naim Fraim; Stillpoints Ultra SS; Symposium Ultra platforms; IsoTek EVO3 Sigmas conditioner; GIK Acoustics absorption and diffusion panels

  10. #10
    Senior Member
    Join Date
    Dec 2018
    Location
    Salem VA
    Posts
    174

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Oh - and also a new pair of Mazda Ciftes coming for the Rhumba Extreme next week as well! Lots of rolling will be going on for sure.
    PRIMARY 2 CH SYSTEM: Backert Labs Rhythm 1.3; Parasound JC3+ Phono pre; Luxman M900u; Pure Fidelity Harmony with Origin Live Illustrious tonearm and PF Stratos cart; Naim NDX 2; Naim 555PS; Innuos Zen MK III (Roon Core); EtherRegen; Volti Audio Rivals; JL Audio e112 (2); Transparent Super Speaker Cables; Transparent Super interconnects; Transparent Premium & High Performance power cables; Naim Fraim; Stillpoints Ultra SS; Symposium Ultra platforms; IsoTek EVO3 Sigmas conditioner; GIK Acoustics absorption and diffusion panels

  11. #11
    Senior Member
    Join Date
    May 2013
    Location
    Tallahassee, Florida/Greenville, SC
    Posts
    3,242

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Interested to see which one you prefer. I also had a bad KT-120 out of quad on new Tung Sols. More common than you think with the new production tubes.
    Main - JVC QL-Y7/Denon DL-301 Mk II, Gold Note PH-10, Jays CDT3 Mk3 , Auralic Aries G2.2, Holo May KTE, Supratek Cabernet, Kinki Studio EX-B7 monoblocks, Verity Audio Otello, (2) Rythmik F12SE, Audio Envy IC, SC & PC's, Triode Wire Lab PC's, Inakustik USB and I2S, (2) Puritan Audio Labs PSM-156 with Groundmaster City, Timbernation rack

    Family Room - Oppo UDP-203, Auralic Aries, Aqua La Voce S3, Kinki Studio EX-M1+, Nola KO, (2) Rythmik F-12G, Wireworld SC & IC's, Neotech PC's, SurgeX SA-1810

    Greenville, SC- Jays CDT2 Mk 3, Auralic Aries G1, Holo Spring 3 KTE, Supratek Chardonnay, Odyssey Audio Kismet Reference, Rosso Fiorentino Volterra 2, (2) RSL Speedwoofers, iFi Audio Power Station, Wireworld IC's, Inakustik USB and I2s, Triode Wire Lab SC, Triode Wire Lab PC's, Furutech NCF Clear Line, Timbernation rack.

  12. #12
    Senior Member
    Join Date
    Dec 2018
    Location
    Salem VA
    Posts
    174

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    As a follow up to this thread... I received the Gold Lion KT88s over the weekend and swapped them out with the Luxman JJs.

    Unfortunately, bad news on the amp... When I went to bias the GLs I noticed the tube sockets in V2 and V3 (where I had the bad JJ tube) were getting unbiased current - the meter snapped right into overload status on both tube sockets. No amount of potentiometer adjustment could bring them back in line.

    The current line of thinking is that when the JJ went bad, it took out the cathode resistor on the amp as well. So unfortunately this will have to go back to Luxman for warranty repair. It seems like I've been dealing with this tube problem for weeks, and now I guess it will be additional weeks before I get a functional amp back. Disappointing since I have only enjoyed the amp for what seems like 20 minutes or so.
    PRIMARY 2 CH SYSTEM: Backert Labs Rhythm 1.3; Parasound JC3+ Phono pre; Luxman M900u; Pure Fidelity Harmony with Origin Live Illustrious tonearm and PF Stratos cart; Naim NDX 2; Naim 555PS; Innuos Zen MK III (Roon Core); EtherRegen; Volti Audio Rivals; JL Audio e112 (2); Transparent Super Speaker Cables; Transparent Super interconnects; Transparent Premium & High Performance power cables; Naim Fraim; Stillpoints Ultra SS; Symposium Ultra platforms; IsoTek EVO3 Sigmas conditioner; GIK Acoustics absorption and diffusion panels

  13. #13
    Super Moderator
    Join Date
    Apr 2013
    Location
    NY
    Posts
    18,726

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    I’m so sorry to see the amp is faulty. That’s such a shame.

    Is there local Luxman warranty repair?
    Fleetwood Deville by Oswald Mills Audio, Vienna Acoustics Haydn Jubilee, Wharfedale Linton w/ stands, Klipsch RB-75, Klipsch RP-160M.

    Job INTegrated. Luxman L-595aSE

    NAD C 658 streamer.

    First Watt SIT-3, Job 250 Monos, NuForce STA200, AkitikA GT-102 amp, ASL Wave monos, Dennis Had 45 monos. Absolute Audio Labs PCF 25 amp (improved First Watt F7 super clone)

    Topping D90, RME Audio ADI-2 DAC FS, ModWright Ultimate Sony XA-5400ES.

    Burmester 948, McIntosh MCLK12, Kimber Kable, Siltech, Cardas, Avanti Audio cables.

  14. #14
    Senior Member
    Join Date
    Dec 2018
    Location
    Salem VA
    Posts
    174

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Thanks Joe, yes it is disappointing, especially with the addition of the Backert Labs pre and the M Scaler at the same time. I feel like this new system is never going to come together!

    Unfortunately I have no local Luxman dealers. I do have a good tube guy here in town but I am sure he's not an authorized warranty shop. My dealer up in DC (Command Performance) has been great helping me work through the problem over the past week. He's reached out to Luxman to see what the next steps are.

    Until then my new Cifte's arrived today for the Backert pre, so it will be fun to imagine what they will sound like through the MQ, LOL.
    PRIMARY 2 CH SYSTEM: Backert Labs Rhythm 1.3; Parasound JC3+ Phono pre; Luxman M900u; Pure Fidelity Harmony with Origin Live Illustrious tonearm and PF Stratos cart; Naim NDX 2; Naim 555PS; Innuos Zen MK III (Roon Core); EtherRegen; Volti Audio Rivals; JL Audio e112 (2); Transparent Super Speaker Cables; Transparent Super interconnects; Transparent Premium & High Performance power cables; Naim Fraim; Stillpoints Ultra SS; Symposium Ultra platforms; IsoTek EVO3 Sigmas conditioner; GIK Acoustics absorption and diffusion panels

  15. #15
    Senior Member
    Join Date
    Dec 2018
    Location
    Salem VA
    Posts
    174

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    As a happy ending....

    Luxman is shipping me a brand-new replacement MQ-88uSE today. Luxman definitely goes above and beyond... great customer service!
    PRIMARY 2 CH SYSTEM: Backert Labs Rhythm 1.3; Parasound JC3+ Phono pre; Luxman M900u; Pure Fidelity Harmony with Origin Live Illustrious tonearm and PF Stratos cart; Naim NDX 2; Naim 555PS; Innuos Zen MK III (Roon Core); EtherRegen; Volti Audio Rivals; JL Audio e112 (2); Transparent Super Speaker Cables; Transparent Super interconnects; Transparent Premium & High Performance power cables; Naim Fraim; Stillpoints Ultra SS; Symposium Ultra platforms; IsoTek EVO3 Sigmas conditioner; GIK Acoustics absorption and diffusion panels

  16. #16
    Super Moderator
    Join Date
    Apr 2013
    Location
    NY
    Posts
    18,726

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Huge Congratulations! I love Luxman. That was smart of them to do that.
    Fleetwood Deville by Oswald Mills Audio, Vienna Acoustics Haydn Jubilee, Wharfedale Linton w/ stands, Klipsch RB-75, Klipsch RP-160M.

    Job INTegrated. Luxman L-595aSE

    NAD C 658 streamer.

    First Watt SIT-3, Job 250 Monos, NuForce STA200, AkitikA GT-102 amp, ASL Wave monos, Dennis Had 45 monos. Absolute Audio Labs PCF 25 amp (improved First Watt F7 super clone)

    Topping D90, RME Audio ADI-2 DAC FS, ModWright Ultimate Sony XA-5400ES.

    Burmester 948, McIntosh MCLK12, Kimber Kable, Siltech, Cardas, Avanti Audio cables.

  17. #17
    Senior Member
    Join Date
    Dec 2018
    Location
    Salem VA
    Posts
    174

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Agree, I was all ready to settle in for a long wait while they shipped it around for service. This is great news. I have been a fan since I picked up my C1010/M2000 combo 2 years ago but this goes the extra mile & confirms my deep affinity for the brand.

    By the way, Joe, how do you like the MQ-300? I've wondered how it performs compared to the MQ-88u given its new Mazda Miata-level price point. What preamp are you running into it?
    PRIMARY 2 CH SYSTEM: Backert Labs Rhythm 1.3; Parasound JC3+ Phono pre; Luxman M900u; Pure Fidelity Harmony with Origin Live Illustrious tonearm and PF Stratos cart; Naim NDX 2; Naim 555PS; Innuos Zen MK III (Roon Core); EtherRegen; Volti Audio Rivals; JL Audio e112 (2); Transparent Super Speaker Cables; Transparent Super interconnects; Transparent Premium & High Performance power cables; Naim Fraim; Stillpoints Ultra SS; Symposium Ultra platforms; IsoTek EVO3 Sigmas conditioner; GIK Acoustics absorption and diffusion panels

  18. #18
    Senior Member
    Join Date
    May 2013
    Location
    Tallahassee, Florida/Greenville, SC
    Posts
    3,242

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Congrats man, glad it all worked out and now you have spare tubes too.
    Main - JVC QL-Y7/Denon DL-301 Mk II, Gold Note PH-10, Jays CDT3 Mk3 , Auralic Aries G2.2, Holo May KTE, Supratek Cabernet, Kinki Studio EX-B7 monoblocks, Verity Audio Otello, (2) Rythmik F12SE, Audio Envy IC, SC & PC's, Triode Wire Lab PC's, Inakustik USB and I2S, (2) Puritan Audio Labs PSM-156 with Groundmaster City, Timbernation rack

    Family Room - Oppo UDP-203, Auralic Aries, Aqua La Voce S3, Kinki Studio EX-M1+, Nola KO, (2) Rythmik F-12G, Wireworld SC & IC's, Neotech PC's, SurgeX SA-1810

    Greenville, SC- Jays CDT2 Mk 3, Auralic Aries G1, Holo Spring 3 KTE, Supratek Chardonnay, Odyssey Audio Kismet Reference, Rosso Fiorentino Volterra 2, (2) RSL Speedwoofers, iFi Audio Power Station, Wireworld IC's, Inakustik USB and I2s, Triode Wire Lab SC, Triode Wire Lab PC's, Furutech NCF Clear Line, Timbernation rack.

  19. #19
    Super Moderator
    Join Date
    Apr 2013
    Location
    NY
    Posts
    18,726

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Quote Originally Posted by JSQT View Post
    Agree, I was all ready to settle in for a long wait while they shipped it around for service. This is great news. I have been a fan since I picked up my C1010/M2000 combo 2 years ago but this goes the extra mile & confirms my deep affinity for the brand.

    By the way, Joe, how do you like the MQ-300? I've wondered how it performs compared to the MQ-88u given its new Mazda Miata-level price point. What preamp are you running into it?

    The MQ-300 is freaking awesome.

    Sweet, smooth, round mids, amazing vocals. A great 300B example of an amp.

    My main preamp now is the Misho Wooden preamp.

    The GAT2, for me, has way too much gain on my Avantgarde Duo..
    Last edited by joeinid; September 3, 2019 at 10:18 PM.
    Fleetwood Deville by Oswald Mills Audio, Vienna Acoustics Haydn Jubilee, Wharfedale Linton w/ stands, Klipsch RB-75, Klipsch RP-160M.

    Job INTegrated. Luxman L-595aSE

    NAD C 658 streamer.

    First Watt SIT-3, Job 250 Monos, NuForce STA200, AkitikA GT-102 amp, ASL Wave monos, Dennis Had 45 monos. Absolute Audio Labs PCF 25 amp (improved First Watt F7 super clone)

    Topping D90, RME Audio ADI-2 DAC FS, ModWright Ultimate Sony XA-5400ES.

    Burmester 948, McIntosh MCLK12, Kimber Kable, Siltech, Cardas, Avanti Audio cables.

  20. #20
    Senior Member
    Join Date
    Apr 2015
    Location
    North Central Florida
    Posts
    3,483

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    JSQT.......I am sorry to read about your Luxman amplifier damage. These kinds of events can take the luster off a brand new purchase. At $5,999.00 for the Luxman MQ88-uSE power amplifier, I would have expected Luxman to incorporate some type of power tube monitor system that would have immediately shut down the amp in the event of a power tube failure. That the KT88 was allowed to remain energized, arcing, creating dangerous voltages that damage the bias section of the amplifier seems unacceptable to me.
    Dan

    STUDIO - McIntosh C1000C/P, MC2301 (2), MR88, Aurender N10, Esoteric K-01X, Shunyata Sigma spdif digital coax,
    Sonos Connect, Stillpoints Ultra SS & Ultra Mini, PurePower 2000, Furutech Flux 50, Michell Gyro SE, Michell HR Power Supply, SME 309, Ortofon Cadenza Black, Sonus faber Amati Anniversario

    LIVING ROOM - McIntosh C2300, MC75 (2), MR85, Magnum Dynalab 205 Signal Sleuth, Sonos Connect, Simaudio MOON Neo 260D-T, Schiit Audio Yggdrasil, Aurender N100H, Shunyata Sigma USB cable,
    Sony DAT 60ES, Nakamichi BX-300, Micro Seiki DD40 w/m505A tonearm, Ortofon Cadenza Blue, PS Audio P10, Furutech Flux 50, Stillpoints Ultra Mini, PMC EB1i, JL Audio f113

    VINTAGE - McIntosh 4300V, McIntosh MA230, Tandberg 3011A tuner, Olive 04HD, JBL 4312A

  21. #21
    Senior Member
    Join Date
    Dec 2018
    Location
    Salem VA
    Posts
    174

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Quote Originally Posted by joeinid View Post
    The MQ-300 is freaking awesome.

    Sweet, smooth, round mids, amazing vocals. A great 300B example of an amp.

    My main preamp now is the Misho Wooden preamp.

    The GAT2, for me, has way too much gain on my Avantgarde Duo..
    I just read the whole thread on the Misho. It sounds amazing!

    I am absolutely thrilled with my Backert Labs Rhumba Extreme. I replaced the stock Mullards with a pair of Mazda Ciftes earlier this week and it's really taken the sound to a different level. All of the things I love about the Rhumba Extreme - the space between the notes, the holographic imaging without losing any detail or adding any tube gooey-ness, the powerful bass and airy top end, are enhanced by the Ciftes. It's like giving the Rhumba Extreme a shot of vitamins.

    Since the MQ-88uSE issues, I've been listening with the L-509X in bypass mode, and it sounds amazing, BUT nothing like that fully encompassing "sitting in the 3rd row" soundstage that the MQ-88uSE/Rhumba Extreme combo was providing.

    I also believe the Rhumba Extreme is a very low gain preamp. I don't have specs handy but it seems like something I read on their website.

    The replacement Luxman is scheduled to arrive tomorrow!
    PRIMARY 2 CH SYSTEM: Backert Labs Rhythm 1.3; Parasound JC3+ Phono pre; Luxman M900u; Pure Fidelity Harmony with Origin Live Illustrious tonearm and PF Stratos cart; Naim NDX 2; Naim 555PS; Innuos Zen MK III (Roon Core); EtherRegen; Volti Audio Rivals; JL Audio e112 (2); Transparent Super Speaker Cables; Transparent Super interconnects; Transparent Premium & High Performance power cables; Naim Fraim; Stillpoints Ultra SS; Symposium Ultra platforms; IsoTek EVO3 Sigmas conditioner; GIK Acoustics absorption and diffusion panels

  22. #22
    Senior Member
    Join Date
    Dec 2018
    Location
    Salem VA
    Posts
    174

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Quote Originally Posted by jdandy View Post
    JSQT.......I am sorry to read about your Luxman amplifier damage. These kinds of events can take the luster off a brand new purchase. At $5,999.00 for the Luxman MQ88-uSE power amplifier, I would have expected Luxman to incorporate some type of power tube monitor system that would have immediately shut down the amp in the event of a power tube failure. That the KT88 was allowed to remain energized, arcing, creating dangerous voltages that damage the bias section of the amplifier seems unacceptable to me.
    Thanks Dan - yes, I really can't explain it. It is hard to believe that a bad tube could take out the resistors like that on an amp as meticulously engineered as the MQ-88uSE. I guess anything in possible, but I am thankful that Luxman did the right thing, no questions asked.
    PRIMARY 2 CH SYSTEM: Backert Labs Rhythm 1.3; Parasound JC3+ Phono pre; Luxman M900u; Pure Fidelity Harmony with Origin Live Illustrious tonearm and PF Stratos cart; Naim NDX 2; Naim 555PS; Innuos Zen MK III (Roon Core); EtherRegen; Volti Audio Rivals; JL Audio e112 (2); Transparent Super Speaker Cables; Transparent Super interconnects; Transparent Premium & High Performance power cables; Naim Fraim; Stillpoints Ultra SS; Symposium Ultra platforms; IsoTek EVO3 Sigmas conditioner; GIK Acoustics absorption and diffusion panels

  23. #23
    Senior Member
    Join Date
    Apr 2015
    Location
    North Central Florida
    Posts
    3,483

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Quote Originally Posted by JSQT View Post
    Thanks Dan - yes, I really can't explain it. It is hard to believe that a bad tube could take out the resistors like that on an amp as meticulously engineered as the MQ-88uSE. I guess anything in possible, but I am thankful that Luxman did the right thing, no questions asked.
    JSQT.......I agree, Luxman certainly rose to the occasion to make it right for you. That speaks volumes for their commitment to Luxman customers.
    Dan

    STUDIO - McIntosh C1000C/P, MC2301 (2), MR88, Aurender N10, Esoteric K-01X, Shunyata Sigma spdif digital coax,
    Sonos Connect, Stillpoints Ultra SS & Ultra Mini, PurePower 2000, Furutech Flux 50, Michell Gyro SE, Michell HR Power Supply, SME 309, Ortofon Cadenza Black, Sonus faber Amati Anniversario

    LIVING ROOM - McIntosh C2300, MC75 (2), MR85, Magnum Dynalab 205 Signal Sleuth, Sonos Connect, Simaudio MOON Neo 260D-T, Schiit Audio Yggdrasil, Aurender N100H, Shunyata Sigma USB cable,
    Sony DAT 60ES, Nakamichi BX-300, Micro Seiki DD40 w/m505A tonearm, Ortofon Cadenza Blue, PS Audio P10, Furutech Flux 50, Stillpoints Ultra Mini, PMC EB1i, JL Audio f113

    VINTAGE - McIntosh 4300V, McIntosh MA230, Tandberg 3011A tuner, Olive 04HD, JBL 4312A

  24. #24
    Senior Member
    Join Date
    Jan 2018
    Location
    saṃsāra
    Posts
    1,047

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Quote Originally Posted by JSQT View Post
    As a follow up to this thread... I received the Gold Lion KT88s over the weekend and swapped them out with the Luxman JJs.

    Unfortunately, bad news on the amp... When I went to bias the GLs I noticed the tube sockets in V2 and V3 (where I had the bad JJ tube) were getting unbiased current - the meter snapped right into overload status on both tube sockets. No amount of potentiometer adjustment could bring them back in line.
    fwiw... does not sound like this was your issue but i will just mention it for reference: last year i ordered a pair of matched 6c33c output tubes for my SET amp, also from viva. similar to your experience, when i installed them there was no amount of bias adjustment that would bring the current down to anything close to an acceptable range. i called viva who sent me another pair... after receiving back the original pair.

    turns out that the measurement (not sure what is being measured here) used to match the tubes on the new pair was 91 and the initial pair was something like 120... so, while the initial set was indeed matched they were passing through way too much current.

    not sure if this is anything other than coincidence, but my experience is that when these tubes start to diminish in performance the bias also needs to be adjusted down.

    in any event, the bias setting of new pair of 6c33c tubes was spot on with all other new pairs i have installed and they have worked flawlessly.

    ...just something to keep in mind.
    viking acoustics berlin r mk2 | air tight atc-5 + atm-300r | clearaudio concept + virtuoso v2 MM | t+a dac8 dsd + kanjiroba diy transport + roon rock
    alp-tone audio analog cables | core audio designs plyKraft 3L | hifi racks ltd podium t5-iii

  25. #25
    Senior Member
    Join Date
    Dec 2018
    Location
    Salem VA
    Posts
    174

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Quote Originally Posted by aKnyght View Post
    fwiw... does not sound like this was your issue but i will just mention it for reference: last year i ordered a pair of matched 6c33c output tubes for my SET amp, also from viva. similar to your experience, when i installed them there was no amount of bias adjustment that would bring the current down to anything close to an acceptable range. i called viva who sent me another pair... after receiving back the original pair.

    turns out that the measurement (not sure what is being measured here) used to match the tubes on the new pair was 91 and the initial pair was something like 120... so, while the initial set was indeed matched they were passing through way too much current.

    not sure if this is anything other than coincidence, but my experience is that when these tubes start to diminish in performance the bias also needs to be adjusted down.

    in any event, the bias setting of new pair of 6c33c tubes was spot on with all other new pairs i have installed and they have worked flawlessly.

    ...just something to keep in mind.
    Interesting... I was considering sending the GLs back to Viva to see if they would swap them out due to this issue. I'm afraid to put them into the new amp in the event they were damaged by the overloaded current. I do know however the problem existed before I put the GLs in, with the flashing out of the Luxman JJs. Kind of a chicken and egg thing, did the JJs cause the overload or was there an issue with the amp to begin with that caused the problem with the tubes. Either way it's impossible to tell if the GLs were okay so I'm probably out of luck on getting a replacement set.
    PRIMARY 2 CH SYSTEM: Backert Labs Rhythm 1.3; Parasound JC3+ Phono pre; Luxman M900u; Pure Fidelity Harmony with Origin Live Illustrious tonearm and PF Stratos cart; Naim NDX 2; Naim 555PS; Innuos Zen MK III (Roon Core); EtherRegen; Volti Audio Rivals; JL Audio e112 (2); Transparent Super Speaker Cables; Transparent Super interconnects; Transparent Premium & High Performance power cables; Naim Fraim; Stillpoints Ultra SS; Symposium Ultra platforms; IsoTek EVO3 Sigmas conditioner; GIK Acoustics absorption and diffusion panels

  26. #26
    Senior Member
    Join Date
    Jan 2018
    Location
    saṃsāra
    Posts
    1,047

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Quote Originally Posted by JSQT View Post
    ...Either way it's impossible to tell if the GLs were okay so I'm probably out of luck on getting a replacement set.
    might be worth finding someone local with a tube tester to check them out, or even sending them back to viva with a description of the problem and have them check them out... i found viva quite nice and willing to help out.
    viking acoustics berlin r mk2 | air tight atc-5 + atm-300r | clearaudio concept + virtuoso v2 MM | t+a dac8 dsd + kanjiroba diy transport + roon rock
    alp-tone audio analog cables | core audio designs plyKraft 3L | hifi racks ltd podium t5-iii

  27. #27
    Senior Member
    Join Date
    May 2013
    Location
    Bucks County PA
    Posts
    3,704

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Quote Originally Posted by JSQT View Post
    I just read the whole thread on the Misho. It sounds amazing!

    I am absolutely thrilled with my Backert Labs Rhumba Extreme. I replaced the stock Mullards with a pair of Mazda Ciftes earlier this week and it's really taken the sound to a different level. All of the things I love about the Rhumba Extreme - the space between the notes, the holographic imaging without losing any detail or adding any tube gooey-ness, the powerful bass and airy top end, are enhanced by the Ciftes. It's like giving the Rhumba Extreme a shot of vitamins.

    Since the MQ-88uSE issues, I've been listening with the L-509X in bypass mode, and it sounds amazing, BUT nothing like that fully encompassing "sitting in the 3rd row" soundstage that the MQ-88uSE/Rhumba Extreme combo was providing.

    I also believe the Rhumba Extreme is a very low gain preamp. I don't have specs handy but it seems like something I read on their website.

    The replacement Luxman is scheduled to arrive tomorrow!
    Bob and Andy were both happy to hear this update. I think he said 10db
    -----------------
    Brian

    Main System -
    Rotel RCD-1572 / Rega P3 > Luxman 505UX Mark II > Fyne Audio F502SPs > Synergistic Cables

    Secondary - OPPO 93 > VAC CLA 1 MKII Pre > Odyssey Stratos > Dynaudio Audience 82s > Tara Labs Cables


  28. #28
    Senior Member
    Join Date
    Dec 2018
    Location
    Salem VA
    Posts
    174

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Quote Originally Posted by Shadowfax View Post
    Bob and Andy were both happy to hear this update. I think he said 10db
    Thanks Brian - I did call Andy and give him an update a few weeks ago; great to call a company and have the president of the company pick up the phone.

    BTW the replacement MQ-88uSE arrived with no issues whatsoever and the stock JJ KT88s sound amazing. I did pop the GLs in there for a moment and the bias was over 900mv, so I pulled them and swapped the JJs back in. I think the original resistor issue must have cooked those Gold Lions unfortunately.

    Everything is sounding gorgeous!

    I do think I am going to hold onto the 509X as well. Not getting the response I was hoping for on Audiogon for that thing and it is too precious an integrated to lose for the kind of pricing I'm seeing. I'm thinking I'll run the Monitor Audio Gold 200s from the 509X and use it to power the front 2 channels of the HT and also change things up a bit music-wise when I want a rest from the tubes.
    PRIMARY 2 CH SYSTEM: Backert Labs Rhythm 1.3; Parasound JC3+ Phono pre; Luxman M900u; Pure Fidelity Harmony with Origin Live Illustrious tonearm and PF Stratos cart; Naim NDX 2; Naim 555PS; Innuos Zen MK III (Roon Core); EtherRegen; Volti Audio Rivals; JL Audio e112 (2); Transparent Super Speaker Cables; Transparent Super interconnects; Transparent Premium & High Performance power cables; Naim Fraim; Stillpoints Ultra SS; Symposium Ultra platforms; IsoTek EVO3 Sigmas conditioner; GIK Acoustics absorption and diffusion panels

  29. #29
    Senior Member
    Join Date
    May 2013
    Location
    Bucks County PA
    Posts
    3,704

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Quote Originally Posted by JSQT View Post
    Thanks Brian - I did call Andy and give him an update a few weeks ago; great to call a company and have the president of the company pick up the phone.

    BTW the replacement MQ-88uSE arrived with no issues whatsoever and the stock JJ KT88s sound amazing. I did pop the GLs in there for a moment and the bias was over 900mv, so I pulled them and swapped the JJs back in. I think the original resistor issue must have cooked those Gold Lions unfortunately.

    Everything is sounding gorgeous!

    I do think I am going to hold onto the 509X as well. Not getting the response I was hoping for on Audiogon for that thing and it is too precious an integrated to lose for the kind of pricing I'm seeing. I'm thinking I'll run the Monitor Audio Gold 200s from the 509X and use it to power the front 2 channels of the HT and also change things up a bit music-wise when I want a rest from the tubes.
    It is really a 3 man operation, Bob, Andy, and Bob's son. Everything is hand built in the back of Bob's house about a mile from me. Some of the circuits in the Pre are patented also. The builds are laid out and assembled beautifully and every pc on the board is straight and perfect. The cases are of decent gauge and the knobs solid and responsive. The Rhythm has a beefier chassis and dual power supplies making it essentially a dual mono design. He had one Rumba Extreme on the bench being custom build with the dual PS.

    They use Hegel H20 for Amplification / test and demo. They use Usher Dancer Mini 2s for speakers in the testing/demos.

    For Bob, it's all about the Pre Amp and I tend to agree.

    Keep us posted.
    -----------------
    Brian

    Main System -
    Rotel RCD-1572 / Rega P3 > Luxman 505UX Mark II > Fyne Audio F502SPs > Synergistic Cables

    Secondary - OPPO 93 > VAC CLA 1 MKII Pre > Odyssey Stratos > Dynaudio Audience 82s > Tara Labs Cables


  30. #30
    Senior Member
    Join Date
    Dec 2018
    Location
    Salem VA
    Posts
    174

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Quote Originally Posted by Shadowfax View Post
    He had one Rumba Extreme on the bench being custom build with the dual PS.
    Now that sounds interesting!

    It is really clear the workmanship and attention to detail on these preamps. You can hold the slab of machined aluminum that is the remote and feel the quality!

    Funny thing, I recently had a retailer call me on the phone and give me a stern talking to about why I would have spent so much money on something so cheap and simple - the guy was looking online at the time saying "have you even seen the inside of these things??" In fact it was the attention to detail and hand-crafted workmanship that drew me to the brand in the first place (well, apart from their stellar online testimonials). I am sure he'd never even seen one in person, let alone listened to one!
    PRIMARY 2 CH SYSTEM: Backert Labs Rhythm 1.3; Parasound JC3+ Phono pre; Luxman M900u; Pure Fidelity Harmony with Origin Live Illustrious tonearm and PF Stratos cart; Naim NDX 2; Naim 555PS; Innuos Zen MK III (Roon Core); EtherRegen; Volti Audio Rivals; JL Audio e112 (2); Transparent Super Speaker Cables; Transparent Super interconnects; Transparent Premium & High Performance power cables; Naim Fraim; Stillpoints Ultra SS; Symposium Ultra platforms; IsoTek EVO3 Sigmas conditioner; GIK Acoustics absorption and diffusion panels

  31. #31
    Junior Member
    Join Date
    Apr 2020
    Location
    Hong Kong
    Posts
    4

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Hi JSQT. Just wondering how is your MQ88-uSE performing so far? Are you using a pre-amp or the variable input in the amplifier?
    I have purchased the Luxman MQ-88uc in September 2019 (though, only received it in end November). I am using it in a minimalist system with a set of ProAc Tablette 10 signature and MHDT Lab Altantis DAC.

    The combo sounds lovely and I like it very much but I am experiencing some kind of issues. I am only using the variable input, adjusting the volume in the amplifier. Suddenly there's no sound from the left channel. I reduce the volume to the minimum and turned it up again and everything went to normal. It only happened three times so far, one in the very beginning and twice last week.
    It made me feel a little bit worried.

    I checked the bias and everything was fine, v4 measure 450mv and all other very near 480mv.

    Any tips of what it could be? My speakers are 10ohms impedance. I was using the 8ohm tap but now changed to the 16ohm just to change something. Sound is very similar, if something different maybe a little bit brighter, not sure.

    Appreciate any feedback. Thank you!

  32. #32
    Junior Member
    Join Date
    Apr 2020
    Location
    Hong Kong
    Posts
    4

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Hi everyone,

    About a year ago I purchased a Luxman MQ-88uC and really like the sound but I have experienced one problem that is distressing me...suddenly there's no sound from the left channel.

    In one year of intense use it has now happened four times. I am using a single source connected directly to the Variable input and after turning the volume down and up a few times the sound eventually comes and no more issues for a few months.

    Since it works well most of the time and I can't replicate the problem it feels awkward to send it to repair service. On the other hand it is very disappointing that such an expensive amplifier has this kind of issues. I changed the driving tubes (both ECC83 and ECC82) to NOS mullard after experiencing the problem the first three times, I had hopes this could solve the problem but it happened again. I have checked the bias current and all seems fine, reading near 480mV in all tubes.

    Has anyone experienced similar issues? Any suggestions would be much appreciated.

    Best regards.

  33. #33
    Junior Member
    Join Date
    Apr 2020
    Location
    Hong Kong
    Posts
    4

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Quote Originally Posted by JSQT View Post
    Hey all,

    Well, my new MQ88-uSE shipped directly from Luxman 2 weeks ago suddenly started making horrendous cracking and popping noises in the left channel last night.

    I swapped sides with all the power tubes and it went away, so I figured maybe one of the left channel tubes wasn't seated properly.

    Tonight after listening for about 2 hours, suddenly the same tube (I assume, now in the right channel) started arcing and sparking inside the tube with the same loud crackling coming now from my right speaker.

    I have no idea what is happening - being a brand new amp, and moreso being a "SE" with premium matched KT88s, this is extremely frustrating. I've had to shut down my entire system until I can get it sussed out, which I assume at the minimum will be getting new tubes from Luxman, and possibly having to ship it back for repair, after only owning for 2 weeks.

    Anyone have any ideas what may be happening here? Could a connection be causing a short? I'm running the output from the Backert Labs Rhumba Extreme directly into the inputs on the Luxman.

    Thanks in advance
    May I know how are you doing with your Luxman amplifier?
    I purchased a Luxman mq-88uc in December 2019 and the variable input sometimes fails and there's zero sound from one of the channels. Moving the volume pot up and down a few times eventually fixes the problem for a while but sooner or later in happens again. I am wondering what to do. The last thing I want is to ship it to the repair centre.

    Thank you.

  34. #34

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    I was really hot for a MQ-88uC a few weeks ago. In my quest for more info on the amp I was told that most of the Mq-88uC's that come in for repair have had different tubes installed than what comes from the factory. No tube rolling recommended by Luxman. I'm sure they sound great with the stock KT88's but I would want to tube roll so it kind of shut me down on this amp. Good luck all.

  35. #35
    Senior Member
    Join Date
    Dec 2018
    Location
    Salem VA
    Posts
    174

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Quote Originally Posted by stereogeek View Post
    I was really hot for a MQ-88uC a few weeks ago. In my quest for more info on the amp I was told that most of the Mq-88uC's that come in for repair have had different tubes installed than what comes from the factory. No tube rolling recommended by Luxman. I'm sure they sound great with the stock KT88's but I would want to tube roll so it kind of shut me down on this amp. Good luck all.
    Yes I never did use the Gold Lions in the MQ-88uSE after that incident. In fact I came across them in one of my “gear boxes” a few days ago and wondered if/what I should ever do with them. I loved what the MQ-88uSE did that made it special (Luxman tube magic!) but even mono-strapping two of them, they did not drive my 100 dB Voltis very well.

    I’m actually close to selling off all of my separates at this point and downsizing to a Technics SU-R1000. It’s on back order until December so I’m currently living with the little brother, the G700MK2. It is a totally unique, different kind of amplifier than any I have heard before. I am hoping (and fairly certain) that the R1000 will blow the G700MK2 out of the water with the additional power and processing capabilities (wondering if their much-touted digital calibration on their phono EQ will beat my JC3+!).
    PRIMARY 2 CH SYSTEM: Backert Labs Rhythm 1.3; Parasound JC3+ Phono pre; Luxman M900u; Pure Fidelity Harmony with Origin Live Illustrious tonearm and PF Stratos cart; Naim NDX 2; Naim 555PS; Innuos Zen MK III (Roon Core); EtherRegen; Volti Audio Rivals; JL Audio e112 (2); Transparent Super Speaker Cables; Transparent Super interconnects; Transparent Premium & High Performance power cables; Naim Fraim; Stillpoints Ultra SS; Symposium Ultra platforms; IsoTek EVO3 Sigmas conditioner; GIK Acoustics absorption and diffusion panels

  36. #36

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    That's really weird that two of them strapped for mono did not drive those 100db Volti's very well. This little 25wpc Carver is driving the absolute crap out of my Razz's. My room is pretty small but still.... Anyway, good luck in your quest to find the right stuff to go with your Rivals, it can be a confusing journey for sure. Cheers.

  37. #37
    Senior Member
    Join Date
    Dec 2018
    Location
    Salem VA
    Posts
    174

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Yes, I should have been more clear… there was plenty of power from even a single MQ88uSE, it wasn’t for lack of power into the Rivals, more that there were certain frequencies where there appeared to be impedance dips or something that just wasn’t a good match between speaker and amp where certain upper-mid frequencies could sound distorted and noisy.
    PRIMARY 2 CH SYSTEM: Backert Labs Rhythm 1.3; Parasound JC3+ Phono pre; Luxman M900u; Pure Fidelity Harmony with Origin Live Illustrious tonearm and PF Stratos cart; Naim NDX 2; Naim 555PS; Innuos Zen MK III (Roon Core); EtherRegen; Volti Audio Rivals; JL Audio e112 (2); Transparent Super Speaker Cables; Transparent Super interconnects; Transparent Premium & High Performance power cables; Naim Fraim; Stillpoints Ultra SS; Symposium Ultra platforms; IsoTek EVO3 Sigmas conditioner; GIK Acoustics absorption and diffusion panels

  38. #38

    Re: New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

    Oh, I see now. The pesky upper mids and lower treble strike once again. That is the area that I am VERY sensitive to any glare or emphasis in that range. I had that glare a few years ago when I moved into my new listening room. I tried everything to get rid of it and nothing would work. I finally bought a new rack and got rid of my solid maple set up with the threaded rods....the glare was gone. Anyway, good luck with your new Technics setup....Cheers.

AudioShark - The Best High End Audio Discussion forum.

AudioShark forum is a leading forum site for High End Audio Discussion, Stereo System Discussion, Home Theater System Discussion, Best Home Stereo System Discussion, Home Theater Installation Discussion etc.

The AudioShark forum was created for sharing the passion of high-end Audio. We have Audiophiles from all over the world participating and sharing their knowledge. From novice to experts, you will find a friendly environment for discussing about High End Audio, Stereo System, Home Theater System, Home Stereo System, Home Theater Installation, Amplifiers, Speakers, Subwoofers, Integrated System, Acoustic treatments & Digital Room Corrections and many more.

At AudioShark, we also have incorporated an exciting Marketplace where members can peruse terrific buys on used gear, as well as meet dealers and discuss the purchase of new gear.

We are as crazy about this hobby as you are! So come on in and join us! Audioshark.org the Friendliest Audio Forum!

Industry Participation Disclosure : The owner and administrator of Audioshark is the owner of Suncoast Audio LLC in Sarasota Florida. Suncoast Audio has a full brick and mortar presence in Sarasota with several great show rooms with many world class brands. More information can be found at http://www.suncoastaudio.com

Audioshark is a community of like minded individuals. Audioshark welcomes participation from all manufacturers and owners of all brands and products. It is our belief that online forums provide a community of like minded audiophiles and music lovers to encourage the growth of this wonderful hobby.

Sincerely,
The Audioshark.org Team

New Luxman MQ88-uSE Problems - KT88 is arcing and popping - Any ideas on what caused this?

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •